Hose and Fittings
 
 
AEROQUIP® HOSE
AEROQUIP® HOSE is the best choice for flexible hose in custom installations. We sell Aeroquip hydraulic hose in bulk lengths so you can cut it to the exact lengths needed for your boat. Then install reusable hose ends with appropriate mandrels. 2651-6 and 2651-8 hose are used for high pressure runs, and have a black rubber covering with wire braid reinforcement inside. 2556-6 is used for low pressure runs. Hose is priced and sold per inch.
HOSE-7500 2651-6 AEROQUIP® 3/8" HIGH PRESSURE HOSE
HOSE-7510 2651-8 AEROQUIP® 1/2" HIGH PRESSURE HOSE
HOSE-7520 2556-6 AEROQUIP® 3/8" LOW PRESSURE HOSE
HOSE-7522 2556-8 AEROQUIP® 5/8" LOW PRESSURE HOSE
 
AEROQUIP is a registered trademark of Aeroquip Corporation.
 
 
 
 
CRIMP-ON HOSE ASSEMBLIES
CRIMP-ON HOSE ASSEMBLIES are an attractive time saving feature for inside hoses if you have a standard system configuration. Latham hose kits contain high pressure thermoplastic hose with brass crimp-on hose ends. Check with your sales consultant to get the correct kit for your installation.
HOSE-3010
#6 SAE X 10"LONG CRIMP-ON HOSE ASSEMBLY
HOSE-3036
#6 SAE X 36"LONG CRIMP-ON HOSE ASSEMBLY
HOSE-3048
#6 SAE X 48"LONG CRIMP-ON HOSE ASSEMBLY
HOSE-3060
#6 SAE X 60"LONG CRIMP-ON HOSE ASSEMBLY
HOSE-3096
#6 SAE X 96"LONG CRIMP-ON HOSE ASSEMBLY
         
HOSE-3192
#6 SAE X 192"LONG CRIMP-ON HOSE ASSEMBLY
HOSE-3240
#6 SAE X 240"LONG CRIMP-ON HOSE ASSEMBLY
HOSE-4010
#8 SAE X 10"LONG CRIMP-ON HOSE ASSEMBLY
HOSE-4036
#8 SAE X 36"LONG CRIMP-ON HOSE ASSEMBLY
HOSE-4048
#8 SAE X 48"LONG CRIMP-ON HOSE ASSEMBLY
         
HOSE-4060
#8 SAE X 60"LONG CRIMP-ON HOSE ASSEMBLY
HOSE-4096
#8 SAE X 96"LONG CRIMP-ON HOSE ASSEMBLY
HOSE-4192
#8 SAE X 192"LONG CRIMP-ON HOSE ASSEMBLY
HOSE-4240
#8 SAE X 240"LONG CRIMP-ON HOSE ASSEMBLY
 
 
 
 
 
REUSABLE HOSE END ASSEMBLIES
REUSABLE HOSE END ASSEMBLIES are an attractive time saving feature for outside hoses if you have a standard system configuration. Latham hose kits contain Aeroquip® hose with reusable chrome hose ends. Check with your sales consultant to get the correct kit for your installation.
HOSE-8585
#6 JIC X 16"LONG CHROME HOSE END ASSEMBLY
HOSE-8583
#6 JIC X 18"LONG CHROME HOSE END ASSEMBLY
HOSE-8582
#6 JIC X 20"LONG CHROME HOSE END ASSEMBLY
HOSE-8589
#6 JIC X 22"LONG CHROME HOSE END ASSEMBLY
HOSE-8584
#6 SAE X 18"LONG CHROME HOSE END ASSEMBLY
         
HOSE-8592
#6 SAE X 20"LONG CHROME HOSE END ASSEMBLY
HOSE-8591
#6 SAE X 22"LONG CHROME HOSE END ASSEMBLY
HOSE-8593
#6 SAE X 24"LONG CHROME END HOSE ASSEMBLY
   
* Please note that these are just typical hose assemblies. More sizes are available and custom assemblies can be cut to a specified length.
 
 
 
 
THRU HULLS
THRU HULLS made of 316 stainless steel provide a convenient and sanitary way to carry fluids and cables through the transom. Shanks on hydraulic thru hulls are 3/4" O.D. and the heads have machined flats for wrenches. Stainless jam nuts and lock washers are included.
THRU-3395 1/8"NPT x 1-1/2" LONG
THRU-3400 1/8"NPT x 3" LONG
THRU-3410 1/4"NPT x 3" LONG
THRU-3414 1/4"NPT x 4" LONG

THRU-3415 1/4"NPT x 5" LONG
         
THRU-3420 1/4"NPT x 1-1/2" LONG
THRU-3414 1/4"NPT x 4" LONG
THRU-7074 1/4"NPT x 3/8"NPT(M)
THRU-7103 Dual #6 SAE X 3/8"Npt(M) X 3-1/2" Long Assembly
 
 
 
 
 
CHROME PLATED BRASS FITTINGS
CHROME PLATED BRASS FITTINGS give your plumbing a custom, finished look while providing the necessary conversions from hose to flare to pipe fittings. Reusable hose ends must be installed with correct mandrel tools, listed below. Pipe fittings require sealant, such as Loctite® or Teflon paste. DO NOT USE TEFLON TAPE! Many fittings are also available in plain brass or stainless steel. Most fittings are available in popular kits or individually. There are too many to list here. Please call for specific sizes.
CHROME FITTINGS
FITC-3700
#6 JIC REUSABLE HOSE END
FITC-3702
#6 SAE REUSABLE HOSE END
FITC-3705
#8 JIC REUSABLE HOSE END
FITC-3710
#8 SAE REUSABLE HOSE END
FITC-3715
#6 JIC PUSH-ON HOSE END
         
FITC-3720
#6 SAE PUSH-ON HOSE END
FITC-3675
1/4 NPT x #6 JIC 90 degrees ADAPTER
FITC-3678
1/4 NPT x #6 SAE 90 degrees ADAPTER
FITC-3677
1/4 NPT x #6 JIC STRAIGHT ADAPTER
FITC-3680
1/4 NPT x #6 SAE STRAIGHT ADAPTER
         
FITC-8364
1/4 NPT x #5 FEMALE INV. FLARE 90 degrees
       
Click here for a complete list of chrome fittings
BRASS FITTINGS
FITB-3658
#6 SAE REUSABLE HOSE END
FITB-3657
#6 JIC REUSABLE HOSE END
FITB-3653
#8 SAE REUSABLE HOSE END
FITB-3654
#8 JIC REUSABLE HOSE END
FITB-3655
#6 SAE x 3/8" PUSH-ON HOSE END
         
FITB-8311
1/4 NPT x 3/8" HOSE BARB
FITB-5000
3/8 NPT x 1/2" HOSE BARB
FITB-1008
1/2 NPT x 5/8" HOSE BARB
FITB-3688
1/4 NPT x # 6 SAE STRAIGHT ADAPTER
FITB-2000
1/4 NPT x # 6 JIC STRAIGHT ADAPTER
         
FITB-3687
1/4 NPT x # 6 SAE 90ºADAPTER
FITB-2010
1/4 NPT x # 6 JIC 90º ADAPTER
FITB-3698
3/8 NPT x # 8 SAE STRAIGHT ADAPTER
FITB-3663
3/8 NPT x #8 JIC STRAIGHT ADAPTER
FITB-3697
3/8 NPT x # 8 SAE 90ºADAPTER
         
FITB-3665
3/8 NPT x # 8 JIC 90ºADAPTER
       
Click here for a complete list of chrome fittings
 
 
 
 
FITTINGS KITS
FITTINGS KITS provide all the brass fittings required inside the boat to complete many of the most common steering installations using pre-assembled hoses as well as bulk hose. Detailed schematics are included.

KFIT-1545 HYNAUTIC® HELM, 1 RAM
KFIT-3709 1275V HELM, 2 RAMS

KFIT-3699 INSIDE FITTINGS KIT: FULL POWER, 1 RAM
KFIT-3703 Inside Fittings Kit: Full Power, 2 Rams
KFIT-3702 INSIDE FITTINGS KIT: FULL POWER, 2 RAMS, 2 PUMPS
         
KFIT-3716 INSIDE FITTINGS KIT: FULL HYD. SYSTEM, MCM VI®, 2 RAMS, 1 HI-VOLUME PUMP
       
HYNAUTIC is a registered trademark of Teleflex Incorporated.
MCM VI is a registered trademark of the Brunswick Corporation.
 
 
 
 
LOCTITE PNEUMATIC/HYDRAULIC SEAL 545®
LOCTITE PNEUMATIC/HYDRAULIC SEAL 545® is a superior sealant for joining pipe fittings. It is non-migrating, non-fouling and fittings are removable.
LOCT-8365 LOCTITE® SEAL 545 (50 mL.)
     
Loctite and Pneumatic/Hydraulic Seal are registered trademarks of Loctite Corporation.
 
 
 
 
MANDRELS
MANDRELS are required to install reusable hose ends on Aeroquip 2651 high pressure hose. Directions are included.
TOOL-7000 MANDREL, #6 JIC
TOOL-7006 MANDREL, #6 SAE
TOOL-7008 MANDREL, #8 JIC/SAE
KTOL-7060 MANDREL KIT; ALL 3 OF THE ABOVE
 
WARNING! DO NOT INSTALL HOSE ENDS ON 2651 HOSE WITHOUT MANDRELS! HOSE FAILURE CAN OCCUR.
 
 
 
  Return to Top of Page  
 
 

© Latham Marine Inc. • 280 S.W. 32nd Court Fort Lauderdale, Florida 33315
Tel: 800-422-7267 * 888-422-7267 * 954-462-3055 • Fax (954) 462-3081

Design by Virtual Thunder